Kit Review
Straight build
Size comparison with a cigarette pack
Detail shots
There's a stand parts slot on the bottom of the Goldion Hammer, so it can stand upright stably.
That said, the Goldion Hammer's handle is pretty short, so you'll need to tilt the body's waist back a little to get a proper standing pose.
Body mode with weapons removed
Parts exclusive to body mode
The face can be swapped between three expressions.
A total of 4 hand types are included.
In addition to Goldymarg, Stealth Gao II and the Gatling Driver are also included.
Stealth Gao II
Underside
There's a stand joint parts piece included exclusively for Stealth Gao II.
Stealth Gao II on the stand
The green active-state cover can be swapped out for a black one.
Engine section articulation
The Gatling Driver.
A good chunk of the Dividing Driver parts from the Cross Frame GaoGaiGar have been reused.
A variety of supplementary parts are included for the various transformations and combinations.
There's also a Nail of Light effect part included.
Leftover parts
Limb articulation
You can pull the hip joints down to extend the range of motion,
and the skirts can be swung completely out of the way to the sides.
Waist articulation.
With the Goldion Hammer attached to the back, deep waist bends are pretty much out of the question anyway.
Poses in bare mode
Goldymarg poses
Special 1 : GOLDY TANK
Supplementary parts needed to configure the Goldy Tank
First, disassemble Goldymarg as shown above.
Disassemble the side skirts as shown on the right, then...
Remove the two backpack cover parts and expand the wheel section as shown above.
Combine the parts as shown above to complete the Goldy Tank's drive unit.
Remove the Goldion Hammer's cover, add the various supplementary parts, then place it on top of the drive unit to complete the Goldy Tank.
Underside
Riding the Goldy Tank
Special 2 : AIR BIKE MODE
Supplementary parts needed to configure Air Bike mode
Arrange and combine the parts as shown above.
Air Bike mode
Underside
The handlebars are articulated.
Riding Air Bike mode
Special 3 : MARG HAND A
Supplementary parts needed to configure Mag Hand A for use with Star GaoGaiGar
Disassemble the Goldion Hammer's handle and add supplementary parts to increase its width and length.
Remove the two backpack covers, then
Pull out the fixing pin from the supplementary parts, arrange them as shown above, and combine.
The completed hand and arm form
The tool section is articulated.
You can also remove the hand and attach a collab joint part instead.
The palm peg plugs into the hole in the Goldion Hammer's handle for a solid, secure fit.
Mag Hand A completed with the Goldion Hammer attached
Special 4 : MARG HAND B
Supplementary parts needed to configure Mag Hand B for use with Star GaoGaiGar
Move the wheels from Goldymarg's hat to the feet, and the side skirts to the legs, then attach them.
Extend the backpack wheels as shown above, remove the two covers, then attach the claw-shaped supplementary parts.
After combining the backpack with Goldymarg, have it take a seated pose as shown above.
Add supplementary parts to the Goldion Hammer handle and combine with Goldymarg to finish.
Mag Hand B with the Goldion Hammer held in hand
Special 5 : MARG HAND C
Supplementary parts needed to configure Mag Hand C for use with Star GaoGaiGar
First, remove the two backpack covers while in Goldymarg mode, then
Attach the claw-shaped supplementary parts used for Mag Hand B to the backpack, and spread out the wheel section as shown above.
Combine the front supplementary parts with the wheel section, then fold the rear skirt and connect it to the lower fixing pin.
The overall pose of Goldymarg is as shown above.
Mag Hand C configured with the hand gripping the Goldion Hammer
Together with Cross Frame Girl GaoGaiGar.